Plumbing Basics: Before Installing a Bathtub
Plumbing Basics: Before Installing a Bathtub
Blog Article
What are your beliefs on Tools You Need to Install a New Bathtub ?
Mounting a bathtub isn't exactly brain surgery, yet it does call for strong plumbing, woodworking, and also often, tiling skills. Changing an old bath tub with a brand-new one is likewise a moderately hard job. If the old tub is easily accessible, the task can relocate immediately; if you have to open up a wall to eliminate the old tub and also place the brand-new bathtub, the job is a lot harder. In either instance, the job is within a residence handyman's skills, although you will require a helper to vacate the old tub as well as set in the new one. Make certain you have certified on your own for the task as well as fit trying it. Instead of hiring a service provider to take control of a halfway-completed job, it is much better to consider employing one before you start. Chances are you might require a specialist plumber to make tube links.
This short article will aid you mount a brand-new tub in your bathroom if you have actually already bought a brand-new bathtub as well as do not need to alter the plan of your previous water supply pipes.
Your tools and also product checklist ought to consist of the following:
Planning for the Setup
To start with, the supporting structure supplied with the bathroom needs to be fitted (if needed) according to the producer's instructions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is necessary to see to it that if the tap comes with a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the taps system to avoid stress on the bath tub.
Fit the flexible faucet adapters to the bottom of the two faucets using 2 nuts and olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet with the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you use every one of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bathroom must currently be ready to be fitted in its final placement.
Removing Old Touches
If you require to replace old taps with new ones as a part of your installation, after that the first thing you ought to do is disconnect the water. After doing so, turn on the taps to drain any kind of water staying in the system. The process of removing the existing faucets can be fairly troublesome due to the limited gain access to that is frequently the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the faucets. Have a towel ready for the continuing to be water that will originate from the pipes. When the supply pipes have been removed, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary faucets from turning during this procedure. As soon as the taps have actually been eliminated, the holes in the bath/basin will need to be cleansed of any type of old securing compound.
Before proceeding to fit the brand-new taps, compare the pipeline links on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new taps to fit.
Setting up the Tub
Using the two wooden boards under its feet, put the bathtub in the needed placement. The wooden boards are valuable in evenly spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto four little points.
The following objective is to ensure that the bath tub is leveled all round. This can be accomplished by examining the level and also changing the feet on the bathtub till the spirit level checks out degree.
To install faucets, fit the bottom of the outermost versatile tap port to the appropriate supply pipeline by making a compression sign up with; after that do the same for the various other tap.
Switch on the water supply as well as examine all joints and also new pipework for leaks and also tighten them if essential. Fill the tub and likewise check the overflow electrical outlet and also the normal electrical outlet for leaks.
Ultimately, repair the bathroom paneling as explained in the supplier's user's manual. Tiling and also sealing around the bath tub should wait up until the tub has been made use of at least when as this will certainly resolve it into its final setting.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will require a plastic adapter to avoid damage to the thread. One end of the port fits on the plastic tail of the tap and the various other end supplies a connection to the current supply pipes.
If you require to fit a monobloc, after that you will call for lowering couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the mounting opening in the bath/basin ensuring that the washing machines are in location between the faucet and the sink. Safeguard the tap in place with the producer given backnut. When the faucet is securely in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with typical faucet connectors. The previous type must be attached to the faucet ends first, tightening up just by hand. The supply pipes can later on be connected to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the location where the bath meets the ceramic tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to fracture a stiff seal, causing the water to penetrate the wall surface between the bathroom and the tiling, causing problems with dampness and also possible leakages to the ceiling below.
You can select from a selection of coloured sealers to assimilate your fixtures as well as fittings. They are marketed in tubes and cartridges, and also can securing spaces as much as a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with spins of drenched newspaper or soft rope. Remember to constantly load the tub with water before securing, to enable the activity experienced when the tub is in usage. The sealer can split rather early if you do not think about this motion prior to securing.
Additionally, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also quickly available on the marketplace. It is suggested to fit the floor tiles utilizing water-resistant or waterproof adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a keen person who reads about How to Install a Bathtub Yourself, I was thinking sharing that article post was valuable. Appreciated our write-up? Please share it. Let another person discover it. Thank you for going through it.
Act, don't delay! Report this page